Where Can I Get My Toaster Oven Repaired

Broil Rack (10-inch) – Part Number: SP0002644

Baking Pan

Fix Number FIX12008402

Manufacturer Office Number SP0002643

Crumb Tray Assembly – Part Number: SP0002652

Nibble Tray Associates

Set Number FIX12008409

Manufacturer Part Number SP0002652

Sourced directly from Breville, this Nibble Tray Associates is an OEM replacement part for select Breville Toaster Ovens. To ensure this will fit your appliance, please see the "Model Cantankerous Reference List" below. The primary purpose of the Crumb Tray is to go along the oven clean and make cleaning effortless. If your Crumb Tray is lost, damaged, or discolored, it needs to be replaced. The Crumb Tray is made of durable metallic and is sold individually. The guess dimensions of this Tray are 14"x11.five".

Wire Rack

Set Number FIX12008408

Manufacturer Function Number SP0002651

This Wire Rack is sourced directly from Breville and is an OEM approved replacement part for Breville Toaster Ovens, to ensure this rack fits your appliance please meet the "Model Cross Reference List" beneath. If your current rack is worn, damaged, or rusty, information technology needs to be replaced. Many customers also cull to buy a second rack to be able to estrus multiple items at the same time. The dimensions of the rack are 11.5"L x 14"Westward, it is made out of metal, and are sold individually.

Baking Pan - Square – Part Number: SP0002649

Wire Rack

Fix Number FIX12008392

Manufacturer Role Number SP0002632

Door Leap

Fix Number FIX12008682

Manufacturer Function Number SP0010504

This is a 18-carat manufacturer-approved replacement part used for select models of Breville Smart Ovens, to ensure this part fits your Oven please see the "Model Cross Reference List" below. The leap provides spring action to forestall the door from falling open up, as well every bit keep the door to shut. If your door no longer has enough tension to close correctly, information technology may exist fourth dimension to supervene upon the Door Spring. This particular is made out of metallic and is approximately 5" long. This function is as well referred to as a Tension Jump. Each spring is sold separately.

Installation Instructions

Joyce from CRESTWOOD, KY

Door jump bankrupt allowing door to drop downwards when opened, and not completely closing during operation

Step ane: Unplug unit
Step 2: Remove anxiety
Pace 3: Remove rear panel (lot of phillips screws)
Step 4: Pull side panel away far enough to remove old jump pieces and install new (I used needle nose pliers to connect bound to door, and then stretch other end to hole on back of unit).
Pace 5: Reapply rear panel, ensuring top goes behind lip of meridian cover
Step half dozen: Reapply feet
Step 7: Note - I believe I removed 32 screws full in order to remove rear console and side panel to consummate job. Read more...

Bottom Element Assembly

Fix Number FIX12008690

Manufacturer Office Number SP0010515

This Lesser Element Assembly is designed for employ in sure Breville Toaster Ovens, to ensure that this office will fit your device, please come across the "Model Cross Reference List" below. The Lesser Element Associates is the primary source of heat in your toaster oven and may need to exist replaced if your apparatus is no longer producing rut or won't plow on. It is approximately 17" in length, includes the glass tube, and is sold individually. It may also exist referred to equally a Heating Assembly.

Bottom Element Set Assembly – Part Number: SP0010494

Bottom Element Prepare Associates

Set up Number FIX12008676

Manufacturer Part Number SP0010494

Installation Instructions

Michael from BOTHELL, WA

Glass on the bottom heating element broke and needed replacement.

Kickoff footstep was to remove the outer housing. I flipped the unit over and removed the screws on the feet and bottom panel. This was almost 20 screws (annotation the front end feet have a screw to secure a cover strip that covers the screws attaching the feet to the unit of measurement). Specifically annotation that at that place is a long screw on one of these feet that you need to proceed rails of and realign into a plate when reassembling. After that, remove all the screws from the back (again, there are a lot of screws to remove, but you volition want to remove both those for the exterior casing besides every bit for those securing the back panel). At present you should be able to lift the housing in order to get the dorsum panel off of the unit. The housing volition not come off still because on the side near the front panel controls are a 5 or vi blackness screws that secure the housing to the control panel. You need a long screwdriver as the metal housing can be sharp in order to remove these screws. Once undone, you should be able to elevator the housing by raising the dorsum starting time every bit it has a metallic lip on the front. With the tilt, you should be able to remove the housing from the lip. With the housing off, unplug the heater element connector from the circuit panel. You might need a pair of pliers to exercise this. The other side of the heater element goes into a wire connector that you lot will need to cut off. I advise cut off the wire connector versus cutting the wires equally there is not a lot of extra wire if y'all need to re-strip the wire to go into a new connector. Yous volition need to cut at to the lowest degree one of the necktie straps to get the wire costless. Later on that, remove the excursion lath, should be 4 screws to become access to the heating element. From inside the toaster, remove 2 screws on the other side that spike a bracket that holds the heating element in place. Removing the heating element was the most difficult challenge as in that location are two tabs on the side with the circuit board that holds the bulbs in place. I used a really small-scale screwdriver to bend the tabs out so that I could remove the bulbs. Even with this, it took a lot of maneuvering with pliers to get the heads of the heater element free. I advise goggles and gloves for this slice as I was worried the glass exteriors would break trying to release them. Once you slide the chemical element out, the bracket should be able to slide off the end. Reassembly was more straightforward, but getting the heating element to seat correctly with the tabs was still a chore. Otherwise, the simply other claiming was lining upwards the screws that held the housing to the front panel. A long magnetized screwdriver would be a good recommendation to do that piece. Finally, the one forepart fit does have a metal bracket that slides and so you need to align that piece before those screws will get in. Read more...